networking-lab-setting-with-gns3
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revision | |||
networking-lab-setting-with-gns3 [2019/02/25 10:24] – [4. Adding a Cisco Router] samer | networking-lab-setting-with-gns3 [2021/08/28 09:58] (current) – samer | ||
---|---|---|---|
Line 4: | Line 4: | ||
During the course on Routing and Switching at ESIB, you will discover different functionalities of GNS3 and get familiar with its various features. | During the course on Routing and Switching at ESIB, you will discover different functionalities of GNS3 and get familiar with its various features. | ||
- | ===== -. Software Download ===== | + | ===== - Software Download ===== |
GNS3 is already downloaded on the Lab PCs. If you need to install it on your PC, you should create an account and download it from [[https:// | GNS3 is already downloaded on the Lab PCs. If you need to install it on your PC, you should create an account and download it from [[https:// | ||
Line 11: | Line 11: | ||
Copy the file '' | Copy the file '' | ||
- | ===== -. Basic Configuration ===== | + | ===== - Basic Configuration ===== |
Start the GNS3 software by double-clicking on the Desktop icon. Select the '' | Start the GNS3 software by double-clicking on the Desktop icon. Select the '' | ||
Line 25: | Line 25: | ||
{{ : | {{ : | ||
- | ===== -. Adding a Cisco Switch ===== | + | ===== - Adding a Cisco Switch ===== |
In order to add a Cisco switch to GNS3, browse and select the '' | In order to add a Cisco switch to GNS3, browse and select the '' | ||
Line 42: | Line 42: | ||
- | ===== -. Adding a Cisco Router ===== | + | ===== - Adding a Cisco Router ===== |
In order to add a Cisco router to GNS3, start by copying the file '' | In order to add a Cisco router to GNS3, start by copying the file '' | ||
Line 57: | Line 57: | ||
Click on Idle-PC finder and wait for the process to complete. Finally, apply to validate the new device parameters. Now you are set to start using Cisco routers with GNS3. | Click on Idle-PC finder and wait for the process to complete. Finally, apply to validate the new device parameters. Now you are set to start using Cisco routers with GNS3. | ||
- | ===== -. Starting a New Project ===== | + | ===== - Starting a New Project ===== |
Choose a name for your project. | Choose a name for your project. | ||
Line 73: | Line 73: | ||
Now you have access to the CLI (Command Line Interface) of the Cisco devices in your network. | Now you have access to the CLI (Command Line Interface) of the Cisco devices in your network. | ||
- | ===== -. Saving your Work ===== | + | ===== - Saving your Work ===== |
During the Lab, you should frequently save the configuration of each of the Cisco devices. For this, you can use the following command to store the running-config into the startup-config (NVRAM). | During the Lab, you should frequently save the configuration of each of the Cisco devices. For this, you can use the following command to store the running-config into the startup-config (NVRAM). | ||
Line 82: | Line 82: | ||
Then, using the '' | Then, using the '' | ||
- | ===== -. Tips and Hints ===== | + | ===== - Tips and Hints ===== |
<WRAP center round tip 100%> | <WRAP center round tip 100%> |
networking-lab-setting-with-gns3.1551086654.txt.gz · Last modified: 2019/02/25 10:24 by samer