Differences

This shows you the differences between two versions of the page.

--- networking-lab-setting-with-gns3 [2019/02/12 16:26] – [2. Basic Configuration] samer
+++ networking-lab-setting-with-gns3 [2021/08/28 09:58] (current) – samer
@@ Line 4: / Line 4: @@
 During the course on Routing and Switching at ESIB, you will discover different functionalities of GNS3 and get familiar with its various features.
-===== -. Software Download =====
+===== - Software Download =====
 GNS3 is already downloaded on the Lab PCs. If you need to install it on your PC, you should create an account and download it from [[https://www.gns3.com/software/download]]. Make sure to choose the right version for your operating system. Moreover, during the first steps of the installation, choose to ''Run only legacy IOS'' as shown below.
@@ Line 10: / Line 10: @@
 {{ :gns3.png?nolink&600 |}}
-Copy the file ''c3725-adventerprisek9-mz.124-15.T14.image'' from the folder ''commun'' to your local ''Downloads'' folder.
+Copy the file ''c3725-adventerprisek9-mz.124-15.T14.image'' from Moodle or from the folder ''commun'' to your local ''Downloads'' folder.
-===== -. Basic Configuration =====
+===== - Basic Configuration =====
 Start the GNS3 software by double-clicking on the Desktop icon. Select the ''Local server'' and ''Don't show this again'' button.
-{{ :gns3-2.png?nolink&600 |}}
+{{ :gns3-capture1.png?nolink&600 |}}
-Now proceed to add an IOS router.
+Configure the local server.
-{{ :gns3-3.JPG?nolink&300 |}}
+{{ :gns3-4.JPG?nolink&600 |}}
-{{ :gns3-4.JPG?nolink&300 |}}
+And click to add an IOS router as shown hereafter.
-===== -. Adding a Cisco Switch =====
+{{ :gns3-3.JPG?nolink&350 |}}
+===== - Adding a Cisco Switch =====
 In order to add a Cisco switch to GNS3, browse and select the ''c3725-adventerprisek9-mz.124-15.T14.image'' in your ''Downloads'' folder. Click yes to copy it to the default images library.
@@ Line 39: / Line 42: @@
-===== -. Adding a Cisco Router =====
+===== - Adding a Cisco Router =====
-In order to add a Cisco router to GNS3, start by copying the file ''c7200-advipservicesk9-mz.150-1.M.bin'' from the folder ''commun'' to your local Downloads folder. Now, go to ''Preferences'', then ''IOS Routers'' and click on ''New''.
+In order to add a Cisco router to GNS3, start by copying the file ''c7200-advipservicesk9-mz.150-1.M.bin'' from Moodle or from the folder ''commun'' to your local Downloads folder. Now, go to ''Preferences'', then ''IOS Routers'' and click on ''New''.
 {{ :router-capture-1.PNG?nolink&600 |}}
@@ Line 54: / Line 57: @@
 Click on Idle-PC finder and wait for the process to complete. Finally, apply to validate the new device parameters. Now you are set to start using Cisco routers with GNS3.
-===== -. Starting a New Project =====
+===== - Starting a New Project =====
 Choose a name for your project.
@@ Line 70: / Line 73: @@
 Now you have access to the CLI (Command Line Interface) of the Cisco devices in your network.
-===== -. Saving your Work =====
+===== - Saving your Work =====
 During the Lab, you should frequently save the configuration of each of the Cisco devices. For this, you can use the following command to store the running-config into the startup-config (NVRAM).
@@ Line 79: / Line 82: @@
 Then, using the ''File'' drop-down menu, you can export your work into a portable project you can use on another machine.
-===== -. Tips and Hints =====
+===== - Tips and Hints =====
 <WRAP center round tip 100%>