wikiroute

networking recipes

User Tools

Site Tools

Trace:
exploring_lora

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Next revisionBoth sides next revision
exploring_lora [2018/10/04 17:43] – [2. Theoretical Study] melhemexploring_lora [2018/10/06 13:52] – [3.1. Modifying the Radio Parameters] samer
Line 15: Line 15:
 In order to design and implement experiments with LoRa, you will use the following devices:   In order to design and implement experiments with LoRa, you will use the following devices:  
  
-  * Arduino Mega (x2).+  * Arduino Mega or Arduino Duemilanove (x2).
   * LoRa shields from [[http://www.dragino.com/products/module/item/102-lora-shield.html|Dragino]] (x2).   * LoRa shields from [[http://www.dragino.com/products/module/item/102-lora-shield.html|Dragino]] (x2).
  
Line 22: Line 22:
   * Give the main characteristics of the LoRa shield from Dragino (www.dragino.com).   * Give the main characteristics of the LoRa shield from Dragino (www.dragino.com).
   * What type of Antenna are you using? Explain the corresponding characteristics.    * What type of Antenna are you using? Explain the corresponding characteristics. 
-  * Give an estimated cost of your platform.+  * Give an estimated cost of your devices.
 </WRAP> </WRAP>
- 
 ==== -. Software Tools ==== ==== -. Software Tools ====
  
Line 32: Line 31:
  
 Unzip the RadioHead library and copy it to your sketchbook library folder as detailed in [[https://www.arduino.cc/en/Guide/Libraries]]. Unzip the RadioHead library and copy it to your sketchbook library folder as detailed in [[https://www.arduino.cc/en/Guide/Libraries]].
- 
-<WRAP center round tip 75%> 
-Note well the location of the library folder on your computer. In the following, you will be required to modify source files located in this folder.  
-</WRAP> 
 ==== -. Installation ==== ==== -. Installation ====
  
Line 44: Line 39:
 Connect the two Arduino devices to USB ports on your computer. If this is the first time you use Arduino IDE, make sure to install the necessary USB drivers by selecting ''Tools'' > ''Boards Manager'' and installing Arduino AVR boards. Connect the two Arduino devices to USB ports on your computer. If this is the first time you use Arduino IDE, make sure to install the necessary USB drivers by selecting ''Tools'' > ''Boards Manager'' and installing Arduino AVR boards.
  
-Now, you have to choose the ''Board'' type as ''Arduino/Genuino Mega 2560'' in the ''Tools'' menu and select the corresponding serial ''Port'' to start programming your Arduino.+Now, you have to choose the ''Board'' type as ''Arduino/Genuino Mega 2560'' or ''Arduino Duemilanove or Diecimilia'' in the ''Tools'' menu and select the corresponding serial ''Port'' to start programming your Arduino.
  
 <WRAP center round tip 75%> <WRAP center round tip 75%>
 For Arduino Mega 2560, additional drivers for Microsoft Windows can be installed from [[http://wch.cn/download/CH341SER_ZIP.html]]. For Arduino Mega 2560, additional drivers for Microsoft Windows can be installed from [[http://wch.cn/download/CH341SER_ZIP.html]].
 </WRAP> </WRAP>
- 
 ===== -. Theoretical Study ===== ===== -. Theoretical Study =====
  
Line 58: Line 52:
   * How does the spreading factor impact the coverage of a LoRa transmitter?    * How does the spreading factor impact the coverage of a LoRa transmitter? 
   * What is the transmission bit rate for each of the following configurations of your LoRa device? Explain your computation.   * What is the transmission bit rate for each of the following configurations of your LoRa device? Explain your computation.
-    * Configuration 1: channel bandwidth = 125 kHz, spreading factor = 7, coding rate = 4/5. +    * Configuration 1: channel bandwidth = 125 kHz, spreading factor = 7, coding rate = 4/5 
-    * Configuration 2: channel bandwidth = 500 kHz, spreading factor = 7, coding rate = 4/5. +    * Configuration 2: channel bandwidth = 500 kHz, spreading factor = 7, coding rate = 4/5 
-    * Configuration 3: channel bandwidth = 125 kHz, spreading factor = 12, coding rate = 1/2.+    * Configuration 3: channel bandwidth = 125 kHz, spreading factor = 12, coding rate = 1/2
   * Compute the receiver sensitivity, assuming the following parameters: channel bandwidth = 125 kHz, spreading factor = 7, coding rate = 4/5, bit error rate (BER) target = 10<sup>-4</sup>, and receiver noise figure = 6 dB. Refer to this {{ :1705.05899.pdf | article}} to determine the mapping between the BER and the SNR.   * Compute the receiver sensitivity, assuming the following parameters: channel bandwidth = 125 kHz, spreading factor = 7, coding rate = 4/5, bit error rate (BER) target = 10<sup>-4</sup>, and receiver noise figure = 6 dB. Refer to this {{ :1705.05899.pdf | article}} to determine the mapping between the BER and the SNR.
   * Compare the computed sensitivity to that provided by the {{ :an1200.22.pdf |Semtech Application Note AN1200.22}} for the same parameters.   * Compare the computed sensitivity to that provided by the {{ :an1200.22.pdf |Semtech Application Note AN1200.22}} for the same parameters.
Line 70: Line 64:
 ==== -. Modifying the Radio Parameters ==== ==== -. Modifying the Radio Parameters ====
  
-Download the {{ :sketch-1819.zip | basic sketches}} that implement a simple LoRa communication between the two devices: a client and a server. Open the sketches with Arduino IDE. Make sure to choose the correct ''Board'' and ''Port'' in the ''Tools'' menu. +Download the {{ :sketch-1819.zip | basic sketches}} that implement a simple LoRa communication between two devices: a client and a server. Open the sketches with Arduino IDE. Make sure to choose the correct ''Board'' and ''Port'' in the ''Tools'' menu. 
  
 Take a look at the source code in ''rf95_client.ino'' and ''rf95_server.ino''. Particularly, the following extract from the ''setup'' function configures the radio parameters of your LoRa devices: Take a look at the source code in ''rf95_client.ino'' and ''rf95_server.ino''. Particularly, the following extract from the ''setup'' function configures the radio parameters of your LoRa devices:
Line 96: Line 90:
 </code> </code>
  
-In order to reduce collisions, configure the central frequency of your LoRa devices as indicated below:+In order to reduce collisions between simultaneous experiments, configure the central frequency of your LoRa devices as indicated below:
  
 ^  Group Number  ^   Frequency     ^ ^  Group Number  ^   Frequency     ^
Line 111: Line 105:
 |       11       |      868.7      | |       11       |      868.7      |
 |       12       |      868.9      | |       12       |      868.9      |
- 
 ==== -. Running Basic Sketches ==== ==== -. Running Basic Sketches ====
  
exploring_lora.txt · Last modified: 2021/10/20 12:52 by samer