exploring_lora
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
exploring_lora [2018/10/04 17:36] – [2. Theoretical Study] melhem | exploring_lora [2018/10/06 14:02] – [4.3. [Classroom activity] Collisions and Packet Delivery Ratio] samer | ||
---|---|---|---|
Line 15: | Line 15: | ||
In order to design and implement experiments with LoRa, you will use the following devices: | In order to design and implement experiments with LoRa, you will use the following devices: | ||
- | * Arduino Mega (x2). | + | * Arduino Mega or Arduino Duemilanove |
* LoRa shields from [[http:// | * LoRa shields from [[http:// | ||
Line 22: | Line 22: | ||
* Give the main characteristics of the LoRa shield from Dragino (www.dragino.com). | * Give the main characteristics of the LoRa shield from Dragino (www.dragino.com). | ||
* What type of Antenna are you using? Explain the corresponding characteristics. | * What type of Antenna are you using? Explain the corresponding characteristics. | ||
- | * Give an estimated cost of your platform. | + | * Give an estimated cost of your devices. |
</ | </ | ||
- | |||
==== -. Software Tools ==== | ==== -. Software Tools ==== | ||
Line 32: | Line 31: | ||
Unzip the RadioHead library and copy it to your sketchbook library folder as detailed in [[https:// | Unzip the RadioHead library and copy it to your sketchbook library folder as detailed in [[https:// | ||
- | |||
- | <WRAP center round tip 75%> | ||
- | Note well the location of the library folder on your computer. In the following, you will be required to modify source files located in this folder. | ||
- | </ | ||
==== -. Installation ==== | ==== -. Installation ==== | ||
Line 44: | Line 39: | ||
Connect the two Arduino devices to USB ports on your computer. If this is the first time you use Arduino IDE, make sure to install the necessary USB drivers by selecting '' | Connect the two Arduino devices to USB ports on your computer. If this is the first time you use Arduino IDE, make sure to install the necessary USB drivers by selecting '' | ||
- | Now, you have to choose the '' | + | Now, you have to choose the '' |
<WRAP center round tip 75%> | <WRAP center round tip 75%> | ||
For Arduino Mega 2560, additional drivers for Microsoft Windows can be installed from [[http:// | For Arduino Mega 2560, additional drivers for Microsoft Windows can be installed from [[http:// | ||
</ | </ | ||
- | |||
===== -. Theoretical Study ===== | ===== -. Theoretical Study ===== | ||
Line 58: | Line 52: | ||
* How does the spreading factor impact the coverage of a LoRa transmitter? | * How does the spreading factor impact the coverage of a LoRa transmitter? | ||
* What is the transmission bit rate for each of the following configurations of your LoRa device? Explain your computation. | * What is the transmission bit rate for each of the following configurations of your LoRa device? Explain your computation. | ||
- | ** Configuration 1: channel bandwidth = 125 kHz, spreading factor = 7, coding rate = 4/5. | + | |
- | ** Configuration 2: channel bandwidth = 500 kHz, spreading factor = 7, coding rate = 4/5. | + | * Configuration 2: channel bandwidth = 500 kHz, spreading factor = 7, coding rate = 4/5 |
- | ** Configuration 3: channel bandwidth = 125 kHz, spreading factor = 12, coding rate = 1/2. | + | * Configuration 3: channel bandwidth = 125 kHz, spreading factor = 12, coding rate = 1/2 |
* Compute the receiver sensitivity, | * Compute the receiver sensitivity, | ||
* Compare the computed sensitivity to that provided by the {{ : | * Compare the computed sensitivity to that provided by the {{ : | ||
Line 70: | Line 64: | ||
==== -. Modifying the Radio Parameters ==== | ==== -. Modifying the Radio Parameters ==== | ||
- | Download the {{ : | + | Download the {{ : |
Take a look at the source code in '' | Take a look at the source code in '' | ||
Line 96: | Line 90: | ||
</ | </ | ||
- | In order to reduce collisions, configure the central frequency of your LoRa devices as indicated below: | + | In order to reduce collisions |
^ Group Number | ^ Group Number | ||
Line 111: | Line 105: | ||
| | | | ||
| | | | ||
- | |||
==== -. Running Basic Sketches ==== | ==== -. Running Basic Sketches ==== | ||
Line 126: | Line 119: | ||
In this section, you will measure the Time on Air (ToA) that is given by the time necessary to transmit a message on the radio interface. You will assess the impact of the spreading factor, bandwidth, coding rate, and message size on the ToA. | In this section, you will measure the Time on Air (ToA) that is given by the time necessary to transmit a message on the radio interface. You will assess the impact of the spreading factor, bandwidth, coding rate, and message size on the ToA. | ||
- | Start by implementing a function on the client that measures the time necessary for sending a message. | + | Start by implementing a function on the client that measures the time necessary for sending a message. |
+ | |||
+ | For example, the scenario for assessing the impact of the spreading factor on the ToA consists of sending 100 messages for three different spreading factors //e.g.,// 7, 9, and 10, and drawing the average ToA or the distribution in a boxplot for comparing the results. | ||
<WRAP center round help 100%> | <WRAP center round help 100%> | ||
Line 151: | Line 146: | ||
The setting for this experiment is unique: | The setting for this experiment is unique: | ||
- | |||
* Only one server is required in the classroom. This server should compute the ratio of successfully delivered packets or PDR. | * Only one server is required in the classroom. This server should compute the ratio of successfully delivered packets or PDR. | ||
* All groups are required to use the same frequency, spreading factor, and coding rate. | * All groups are required to use the same frequency, spreading factor, and coding rate. |
exploring_lora.txt · Last modified: 2021/10/20 12:52 by samer