exploring_lora
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
exploring_lora [2018/09/27 16:35] – [4.1. Time on Air] samer | exploring_lora [2018/09/29 12:59] – [3.1. Modifying the Radio Parameters] samer | ||
---|---|---|---|
Line 28: | Line 28: | ||
Download the following software on your PC: | Download the following software on your PC: | ||
- | * RadioHead: The Packet Radio library for embedded microprocessors can be downloaded from [[http://www.airspayce.com/mikem/ | + | * RadioHead: The Packet Radio library for embedded microprocessors can be downloaded from [[https://github.com/samerlahoud/ |
* Arduino IDE: Specific OS versions can be downloaded from [[https:// | * Arduino IDE: Specific OS versions can be downloaded from [[https:// | ||
Line 36: | Line 36: | ||
Note well the location of the library folder on your computer. In the following, you will be required to modify source files located in this folder. | Note well the location of the library folder on your computer. In the following, you will be required to modify source files located in this folder. | ||
</ | </ | ||
- | |||
==== -. Installation ==== | ==== -. Installation ==== | ||
Line 63: | Line 62: | ||
</ | </ | ||
+ | In the remainder of this lab, you will conduct measurements to validate the obtained theoretical receiver sensitivity. | ||
===== -. Configuring and Running the Lab ===== | ===== -. Configuring and Running the Lab ===== | ||
==== -. Modifying the Radio Parameters ==== | ==== -. Modifying the Radio Parameters ==== | ||
- | Start by setting | + | Download the {{ : |
+ | |||
+ | Take a look at the source code in '' | ||
+ | |||
+ | * Central frequency (freq) | ||
+ | * Spreading Factor (SF) | ||
+ | * Bandwidth (Bw) | ||
+ | * Coding Rate (CR) | ||
+ | * Transmit power (Pow) | ||
+ | |||
+ | <code c++> | ||
+ | rf95.setFrequency(frequency); | ||
+ | // Setup Power,dBm | ||
+ | rf95.setTxPower(13); | ||
+ | |||
+ | // Setup Spreading Factor (6 ~ 12) | ||
+ | rf95.setSpreadingFactor(7); | ||
+ | |||
+ | // Setup BandWidth, option: 7800, | ||
+ | //Lower BandWidth for longer distance. | ||
+ | rf95.setSignalBandwidth(125000); | ||
+ | |||
+ | // Setup Coding Rate: | ||
+ | rf95.setCodingRate4(5); | ||
+ | </ | ||
+ | |||
+ | In order to reduce collisions, configure | ||
^ Group Number | ^ Group Number | ||
Line 83: | Line 109: | ||
| | | | ||
- | For this, open the '' | ||
- | |||
- | <file cpp RH_RF95.cpp> | ||
- | setFrequency(86X.Y); | ||
- | </ | ||
- | |||
- | The typical configuration for LoRa modules consists of 125 kHz sub-channels, | ||
- | |||
- | * Bw125Cr45Sf128 | ||
- | * Bw125Cr48Sf4096 | ||
- | * Bw31_25Cr48Sf512 | ||
- | |||
- | Radio configuration is applied in '' | ||
- | <file cpp RH_RF95.cpp> | ||
- | setModemConfig(Bw125Cr45Sf128); | ||
- | </ | ||
==== -. Running Basic Sketches ==== | ==== -. Running Basic Sketches ==== | ||
- | Download the {{ : | + | Now you can compile and upload |
[{{ : | [{{ : | ||
[{{ : | [{{ : | ||
- | |||
- | In the remainder of this lab, you will conduct measurements to validate the obtained theoretical receiver sensitivity. | ||
===== -. Performance Evaluation ===== | ===== -. Performance Evaluation ===== | ||
In the following, you will design and implement a set of scenarios that enable to evaluate the performance of the LoRa modulation. As you will deal with scientific assessment, you are required to use scientific tools to show the results. You have the choice between [[http:// | In the following, you will design and implement a set of scenarios that enable to evaluate the performance of the LoRa modulation. As you will deal with scientific assessment, you are required to use scientific tools to show the results. You have the choice between [[http:// |
exploring_lora.txt · Last modified: 2021/10/20 12:52 by samer